Home > Devices > High End Vaporizers >

  Project Sub-Ohm® "thinmaN"™ 150 Watts iPV3 Mod by Pioneer4you (Black)
Black Project Sub-Ohm "thinmaN" 150 Watts iPV3 Mod


 
Alternative Views:


Our Price: $139.99

Stock Status: (Out of Stock)

Product Code: TMM001

Save on Flavor of the Week

  
Save on Batteries

  
Save on Chargers

  
Save on Wicks

  
Save on Wires

  
Save when buy together

VaporDNA™ Edition Unicorn Refillable E-Juice Bottle (30ml) [Add $1.25]

Coil Master 521 Tab Mini Elite Ohm Meter [Add $18.99]

Black Coil Magician Automatic Coil Jig [Add $28.99]

Coil Master Ceramic Tweezer [Add $8.99]

VaporDNA™ VapeBand™ [Add $1.49]

Qty:  
Description
 
Project Sub-Ohm™ "thinmaN" Black Edition Sold Out! Stay Tuned For More Innovative Products From Project Sub-Ohm™.

Welcome The Big Uncle Of the "littlemaN"™! Project Sub-Ohm™ Has Created The "thinmaN"™ 150 Watts Mod!

WARNING!!! FOR USE WITH 30 AMPS OR HIGHER IMR BATTERIES ONLY!

NOTE: All Project Sub-Ohm "thinmaN"™ 150 Watts Mod Are Serialized!

***This Listing Is For "thinmaN"™ Mod Only!


Made By Pioneer4you X Project Sub-Ohm™

Even since the introduction of the "littlemaN'™, "suitcase"™ and "fatbaby"™ Box mods, each creation has gain a huge popularity among the world of vapers! Now Project Sub-Ohm™ has found the perfect platform to build on its FOURTH box mod. The "thinmaN"™ 150 Watts iPV3 Mod made by Pioneer4you. The goal is simple, to create an affordable and even more powerful device that can satisfy the vapers out there!

Product Includes:
  • 1 "thinmaN"™ Mod by Project Sub-Ohm™
  • 1 USB Cord (For Upgrade Firmware Only! Not For Charging)

Product Descriptions:


The "thinmaN"™ series by Project Sub-Ohm™ is a powerful Variable Wattage Device that can adjustable it's power from 7W to 150W in increments of 0.1 Watts! This device uses an upgraded YiHi SX330 Chip, which is capable of firing coils at 0.1 ohm up to 3.0 ohm. The "thinmaN"™ Mod is powered by dual IMR 18650 battery and is capable of producing up to 150 Watts of power! The two screws on the back of the device hold the battery cover firm and sturdy. The battery is removable. The OLED screen is bright and easy to read, and also shows you the wattage, resistance, output voltage and battery life.


Product Features:
  • Uses latest YiHi SX330 V3s Chip
  • Firmware is upgradeable via USB Port, up to 180 Watts
  • Full Aluminum Body For rigidity!
  • Capable of firing 0.1 ohm - 3.0 ohm build
  • Capable of putting out 150 Watts of power!
  • Reverse Polarity Protection
  • Output Short Protection
  • Low Resistance Protection
  • Battery Low Voltage Protection
  • Temperature Overheat Protection
  • Beautifully Engraved With Project Sub-Ohm™ Logo and "thinmaN"™ logo
  • Serialized for that personal touch
  • Matches all other Project Sub-Ohm™ products
  • NOTE: Touch Sensor Plate Does Not Work On ALL IPV3s
  • The USB cable included in the IPV3s are for firmware upgrade only! Does not charge the device!

Product Specs:
  • Output Power: 7W - 150W
  • Output Voltage: 1.0V - 7.0V
  • Input Current: 30A
  • Input Voltage: 6.2V - 8.5V
  • Loading Resistance: 0.1 ohm - 3.0 ohm
  • Low Resistance Protection
  • High Input Voltage Warning
  • Output Short Circuit Protection
  • Reverse Battery Protection

Product Recommendations:
  • FOR USE WITH 30 AMPS OR HIGHER IMR BATTERIES ONLY!
  • Please do not put in your battery in wrong direction
  • Make sure battery sit completely snug in the battery slot
  • Do not use any batteries if the outside wrapper has come off!
  • Turn off the device before pulling your battery out
  • Do not wrap your coils below 0.2 ohm and always vape safe!

Warning: Project Sub-Ohm™ is a product design and development studio for Electronic Cigarettes and do not involve in any product manufacturing process. Use this product at your own risk. In no event, regardless of cause shall VaporDNA™ and Project Sub-Ohm™ be liable for any type of bodily injury or property damage.

***Always turn off the device and take the battery out when not in use!

Advanced User Item. Use AT YOUR OWN RISK!

FOR USE WITH 30 AMPS OR HIGHER IMR BATTERIES ONLY!!!


NOTE: There is an inherent risk with the use of any and all rechargeable batteries in any circumstance. VaporDNA™ and any and all of VaporDNA™'s parent and subsidiary companies are not responsible for damage if there is any modification of the batteries/chargers in any form or shape (including pack making). VaporDNA™ and any and all of VaporDNA™'s parent and subsidiary companies are not responsible for any damage caused by the misuse and/or mishandling of Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable batteries and chargers.

Use special caution when working with Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells, as they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the user has enough knowledge of Li-Ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells in charging, discharging, assembly and storage before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. Do not use any rechargeable battery as well as any battery charger if any visible damage is present, as well as if the cell or charger has been stressed through mishandling, accidental or otherwise, even if damage may not be visible. Always store and transport rechargeable cells in a safe, non-conductive container in a controlled environment. Dispose of all battery cells and chargers in accordance to local laws and mandates.

VaporDNA™ will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable battery/batteries. Please have a basic understanding of the batteries you are using and how to care for them properly.

Project Sub-Ohm™ is a sub-division of VaporDNA™.
All pictures are based on practicality, copyright reserved.

Average Rating: 5 of 5 Total Reviews: 15 Write a review »

  0 of 0 people found the following review helpful:
 
iPV3 "thinmaN", P.S.O. by VaporDNA.com #1! January 26, 2015
Reviewer: Matthew Green from Ogden, UT United States  
The Pioneer 4 You iPV3 dual 18650 150w, 0.15ohm APV device is OUTSTANDING!! Power output is consistent and reliable. Ohm meter finds applicable voltage for my wattage level every time. The touch sensor is disabled, which is fine with me since I never used it on my iPV2. I wish they(Pioneer4You) would have removed the sensor button and reworked the chassis to not have it there. But no big deal. Has a floating brass 510 connection, so all attys fit flush and clean. Beveled edges are comfortable and very good looking. Has a Evolv DNA-like display that is very intuitive and easy to read. The USB port is for software upgrades ONLY!

***FOR UPGRADES, ALWAYS MAKE SURE TO REMOVE BATTERIES IN THE DEVICE BEFORE PLUGGING INTO THIS PORT!!!



Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
Just....Sexy December 6, 2014
Reviewer: Justin from Livingston, TX United States  
Some would say that this is just your ordinary iPV3.  Dual-18650 variable wattage device, capable of 150watts...yadda-yadda.  If you want an iPV3, then this is absolutely that (as well).  There are countless reviews on the iPV3.  I bought the Project Sub-Ohm because I wanted an iPV3 that was slightly more aesthetically pleasing, and the "thinmaN" does that...and because I very much enjoyed the history behind the Manhattan Project.  This little monster does Oppenheimer proud, and if you don't use extreme caution, will provide quite the fissionable experience.

It's quite simply put...sexy.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
awesome box mod with sick logo December 1, 2014
Reviewer: chase walker from suprise, AZ United States  
First let me say vapordna is waesome had a problem withe the first ipv3 i recived, they told me they would replace it with out a return but it would have to be in silver (i wantes the black one) which i was kinda sad about.... BUT when i recives the package which was 2 days after i called it was black.. Just the best kinda of customer serive u can get.

Now on to the device.. I love it. I know own 3 project sub ohms box mods. The ipv2, the 100w, and now the sexy ipv3... Awesome hob guys. Keepe them coming!! #vapinghappy

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Must have November 30, 2014
Reviewer: Miguel Lodeiro from MIAMI, FL United States  
This is one device you must have if you love vaping. Performance excellent, style excellent, finish excellent, compatibility excellent. From time to time something awesome is released in vaping, this is the time for the thinman.
Honestly is rare when I vape over 50 watts, but feels good knowing you have the power available. From time to time I want to watch that gigantic cloud and this makes it.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
Awesome. November 27, 2014
Reviewer: Noble from Maple Ridge, BC Canada  
I previously had the ipv2 and I was quite satisfied with it but the single 18650 just didn't meet my needs especially considering I often chain vape at 50 watts.  The dual battery of the ipv3 seems to last about 3 times longer than my ipv2 did on a single charge.

I'll be the first to admit, the device can use an improvement or two.  I don't mind the fact that the touch fire sensor doesn't work, but it would be nice if they just went to a magnetic back door already but then again, drilling and epoxying a couple magnets isn't that hard.

Also, it would've been nice if you were able to charge through the USB port like the ipv2 but perhaps I'm asking for too much here.

Overall, I don't regret my purchase at all.  I'd definitely recommend this device to my friends since its versatility is second to none.

Was this review helpful to you?

View All Customer Reviews