The iPV3 Li V2 165W Temperature Control Box Mod by Pioneer4You is one of the most feature packed devices in today's market, combining 165 Watts of power, temperature control features, a smooth sliding door, and the capability to be upgraded to 200 Watts after the appropriate firmware update!
The iPV3 Li V2 by Pioneer4you is one of the most feature packed box mods in today's market, combining 165 Watts of adjustable power, temperature control functions, and a ball locking sliding door, now coming in an all new finish! Utilizing two 18650 batteries (not included) , the iPV3 Li V2 uses a YiHi SX330V3SL Chip, providing incredible accuracy and range, firing resistances from 0.1 to 3.0 ohms with adjustments from 10 to 99.9 Watts in increments of 0.1 Watts, and 100 to 165 Watts in increments of 1 Watt. With efficiency ratings of over 95%, the iPV3 Li is truly the current pinnacle of regulated box mods. Fully integrated temperature control is also present, with adjustments from 212 to 572 degrees Fahrenheit, firing temperature mode resistances down to 0.05 ohms. Manufactured out of Aluminum, the iPV3 Li V2 features a dovetail sliding door with a ball locking mechanism. A spring-loaded brass 510 connection makes adjustment and atomizer connection consistent and hassle free. Utilizing the Micro USB port, user's will also have the opportunity to upgrade the iPV3 Li V2 to 200 Watts once the firmware update becomes available.
Please Note: Batteries must be matched in brand, model and battery state at all times. Discharge and recharge batteries within the same grouping of two. Failure to do so may result in injury. Never use damaged or improperly wrapped batteries with this device.
Product Features and Specs:
- Billet Aluminum body
- YiHi SX330V3SL Chip
- Utilizes two high amp 18650 batteries (sold separately)
- Three button design
- Micro USB port for updates
- Dovetail Sliding and Ball Locking Door
- Brass 510 spring loaded connection
- Output wattage range of 10w-165w
- Atomizer Resistance: 0.10 ohm - 3.0 ohms
- 212 to 572 Degrees Fahrenheit
- Temp Atomizer Resistance: 0.05 ohm - 0.3 ohm
- 0.96" OLED Screen
- Output voltage: 1.0V - 7.5V
- Input current: 1.3A - 40A
- Input voltage: 6.2V - 8.5V
- Reverse polarity protection
- Battery low voltage protection
- Low resistance protection
- Temperature overheat protection
- Output short circuit protection
What's in the Box:
- One iPV3 Li V2 Box Mod
- One User Manual
- One USB cable for updates
- One Warranty Card
- Utilize ONLY 20 Amp or higher IMR/INR Batteries!
- 18650 Batteries are NOT included!
- In order to use temperature control output, coils must be built using non-resistant wire.
- Do NOT go above manufacturer recommended amperage or wattage limits!
Advanced User Item. Use at Your Own Risk! Do Not Fire Atomizer Resistance Lower Than 1 Ohm!
NOTE: There is an inherent risk with the use of any and all rechargeable batteries in any circumstance. VaporDNA™ and any and all of VaporDNA™'s parent and subsidiary companies are not responsible for damage if there is any modification of the batteries/chargers in any form or shape (including pack making). VaporDNA™ and any and all of VaporDNA™'s parent and subsidiary companies are not responsible for any damage caused by the misuse and/or mishandling of Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable batteries and chargers.
Use special caution when working with Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells, as they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the user has enough knowledge of Li-Ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells in charging, discharging, assembly and storage before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. Do not use any rechargeable battery as well as any battery charger if any visible damage is present, as well as if the cell or charger has been stressed through mishandling, accidental or otherwise, even if damage may not be visible. Always store and transport rechargeable cells in a safe, non-conductive container in a controlled environment. Dispose of all battery cells and chargers in accordance to local laws and mandates.
VaporDNA™ will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable battery/batteries. Please have a basic understanding of the batteries you are using and how to care for them properly.
All pictures are based on practicality, copyright reserved.