Smoant Campbel 80W Starter Kit
The Smoant Campbel 80W Starter Kit is a unique vaping device that utilizes a dual segment atomizer system in order to pull vapor from the sub-ohm tank through the secondary chamber filled with your favorite carbonated beverage. The Campbel Box Mod has a maximum output of 80W and requires a single 18650 battery (sold separately). This box mod has a non-adjustable battery dependent power output with a maximum of 80W, a voltage output range of 3.2 to 4.2V, and an atomizer resistance range of 0.08 to 3.0 ohm. The single button interface can lock the box mod with five successive button presses. The LED battery state indicator shows three LEDs for 4.2 to 3.9V, two LEDs for 3.9 to 3.6V, and one LED for 3.6 to 3.2V. The Micro USB port has a maximum charge rate of 1A. The battery can be accessed through a sliding latch battery access door at the bottom of the device. The Campbel Tank and Filter combination is 113mm tall and can be fully disassembled for cleaning. The Campbel's dual segment tank features a 54mm tall glass tube containing a threaded top cap, mesh tube, and aluminum alloy sleeve with a viewing port. This top segment has a 3ml liquid filling capacity. The bottom tank segment has a separate threaded top cap for e-liquid refill and an aluminum alloy sleeve with viewing port. This sub-ohm tank uses the proprietary Campbel Ni80 replacement coil and has a 2ml E-Liquid capacity. The Campbel Replacement Coil uses an Ni80 heating material, has a 0.2 ohm atomizer resistance, and a recommended power output of 30 to 60W. The upper segment of the Campbel has a 9mm wide proprietary ULTEM drip tip that has two sealable 4mm by 2mm air ports. The Smoant Campbel 80W Starter Kit is a unique device that allows the users to blend two unique flavors in order to open up a new world of flavor.
Monthly Featured Flavors
Please Note: Batteries must be matched in brand, model and battery state at all times. Discharge and recharge batteries within the same grouping of two. Failure to do so may result in injury. Never use damaged or improperly wrapped batteries with this device.
Campbel Box Mod Features:
- 80W Maximum Output
- 18650 Battery Required
- Sold Separately
- 3.2V to 4.2V Output
- 0.08 to 3.0 ohm Atomizer Resistance Range
- Micro USB Charge Port
- Single Over-Sized Button Interface
- Output Dependent on Current State of Battery
- LED Battery State Indicator
- 4.2 to 3.9V
- 3.9 to 3.6V
- 3.6 to 3.2V
- Low Power, Less than 3.2V
- Micro USB Port Charging
- Sliding Latch Bottom Battery Access Door
- Gold Plated 510 Connection
Campbel Tank & Filter Features:
- 24mm Diameter
- Dual Segment Tank
- Top Segment
- Threaded Top Cap
- Mesh Tube
- Aluminum Alloy Sleeve with Viewing Port
- 54mm Glass Tube
- 3ml Liquid Capacity
- Bottom Tank Segment
- Separate Threaded Top Cap
- Aluminum Alloy Sleeve with Viewing Port
- Campbel Ni80 Replacement Coil
- 2ml E-Liquid Capacity
- Campbel Replacement Coil
- Ni80 Heating Material
- 0.2 ohm
- 30 to 60W
- 9mm Wide Proprietary ULTEM Drip Tip
- Built-In Airflow
- Dual 4mm by 2mm Air Ports
- Stainless Steel, Aluminum Alloy, Resin and Quartz Glass Construction
- One Campbel 80W Box Mod
- One Campbel Tank
- Two Campbel Ni80 Replacement Coils
- One Replacement Upper Glass Segment
- One Replacement Lower Glass Segment
- One Spare Parts Pack
- One Micro USB Cable
- One Certificate Card
- One Battery Warning Card
- One Warranty Card
Warning: Never use a short or flat 510 connection on any hybrid or hybrid style device. If unsure whether this pertains to your particular set-up, DO NOT assemble and use. Always use proper precautions and handling.
Advanced User Item. Use At Your Own Risk!
NOTE: Descriptions, specifications, and claims are based on manufacturer information. Information listed and provided are to be used at the sole discretion of the consumer and are not representative of analysis, testing, and verification by VaporDNA and any and all of VaporDNA's parent and subsidiary companies. There is an inherent risk with the use of any and all rechargeable batteries in any circumstance. VaporDNA® and any and all of VaporDNA®'s parent and subsidiary companies are not responsible for damage if there is any modification of the batteries/chargers in any form or shape (including pack making). VaporDNA® and any and all of VaporDNA®'s parent and subsidiary companies are not responsible for any damage caused by the misuse and/or mishandling of Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable batteries and chargers.
Use special caution when working with Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells, as they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the user has enough knowledge of Li-Ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells in charging, discharging, assembly and storage before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. Do not use any rechargeable battery as well as any battery charger if any visible damage is present, as well as if the cell or charger has been stressed through mishandling, accidental or otherwise, even if damage may not be visible. Always store and transport rechargeable cells in a safe, non-conductive container in a controlled environment. Dispose of all battery cells and chargers in accordance to local laws and mandates.
VaporDNA® will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable battery/batteries. Please have a basic understanding of the batteries you are using and how to care for them properly.
All pictures are based on practicality, copyright reserved.